It is currently Wed Dec 01, 2021 9:21 pm

All times are UTC - 5 hours [ DST ]




  Page 1 of 1   [ 14 posts ] New Topic Add Reply
Author Message
PostPosted: Fri Apr 23, 2021 1:41 pm • # 1 
User avatar
Full Member

Joined: 02/06/13
Posts: 114
Has anyone cast or fished an RDP 0wt stretched out to 9'4" and made to a 5pc with inserting a 2wt butt in to it? I've toyed with a similar thought for a while and Mark confirmed the idea for me this morning. I want a longer rod for tricos and super light swinging but tenkara is not appealing to me.


Top
  
PostPosted: Fri Apr 23, 2021 9:13 pm • # 2 
User avatar
Full Member

Joined: 07/20/19
Posts: 115
Location: North Central Indiana
toothybugs wrote:
Has anyone cast or fished an RDP 0wt stretched out to 9'4" and made to a 5pc with inserting a 2wt butt in to it?


Love to shock you and say "Why yes, I have done precisely that before!". But alas, I cannot. Interesting idea and it might make a great rod if you can get the transition to your liking. I know of folks who mix/match sections and they say it works just fine to their assessments.

I think some of the earlier Euro-nymph experiments involved swapping sections to explore the design of what are now manufactured ESN blank concepts.

Heck, I built on a Sage RPL+ 6wt blank long ago and the aggressive change from the butt to the tip proved that the field is wide open and structurally pretty functional for dramatic differences in flex characteristics over 9' of blank. That was an extreme blank for a 6wt.


Top
  
PostPosted: Wed May 19, 2021 11:47 am • # 3 
User avatar
Full Member

Joined: 02/06/13
Posts: 114
Well the blank should be showing up early next week. I'll report back on how it does and my thoughts on it. I'm expecting it to be more like a very willowy true 00 than anything.


Top
  
PostPosted: Wed May 19, 2021 11:59 am • # 4 
User avatar
Sr. Member

Joined: 09/09/14
Posts: 469
Location: southern Brazil
toothybugs wrote:
Well the blank should be showing up early next week. I'll report back on how it does and my thoughts on it. I'm expecting it to be more like a very willowy true 00 than anything.


So what blank did you order? Possibly the RDP 7.5 foot 0-weight?


Top
  
PostPosted: Wed May 19, 2021 1:26 pm • # 5 
User avatar
Full Member

Joined: 02/06/13
Posts: 114
PampasPete wrote:
toothybugs wrote:
Well the blank should be showing up early next week. I'll report back on how it does and my thoughts on it. I'm expecting it to be more like a very willowy true 00 than anything.


So what blank did you order? Possibly the RDP 7.5 foot 0-weight?


Correct, with a spare 2wt butt section. I'll probably stent it to make it an even 9'6" though.


Top
  
PostPosted: Wed May 19, 2021 5:26 pm • # 6 
User avatar
Sr. Member

Joined: 09/09/14
Posts: 469
Location: southern Brazil
I think it would be worth your while to use the Common Cents System and run some tests before building it out all the way: first with the upper 3 sections of the 7'6" rod, then with all four sections, and finally with the extra 2-weight section. The results may be surprising, but that will tell you better what to expect before going all out.


Top
  
PostPosted: Wed May 19, 2021 9:14 pm • # 7 
User avatar
Hero Member

Joined: 05/28/18
Posts: 596
Location: Tucson , Hellazonia
I have the 7'6" 0 wt and it's too willowy for me to even thing about going longer . Good luck .


Top
  
PostPosted: Thu May 20, 2021 9:12 am • # 8 
User avatar
Full Member

Joined: 02/06/13
Posts: 114
Good thought, and thanks. I had some fun with this though - I ordered 2 copies of the 7'6" #0, one with the extra butt section, and a spare tip if one of them pops. I am only planning to build the 5-section rod first so if it's a disaster I've built some redundancy/ fall-back in to my plan. I already have a 5ft-something 0wt (Ben's of Holland glass) so I don't need the 3-section 0wt.

PampasPete wrote:
I think it would be worth your while to use the Common Cents System and run some tests before building it out all the way: first with the upper 3 sections of the 7'6" rod, then with all four sections, and finally with the extra 2-weight section. The results may be surprising, but that will tell you better what to expect before going all out.


Top
  
PostPosted: Mon Jul 19, 2021 8:17 am • # 9 
User avatar
Full Member

Joined: 02/06/13
Posts: 114
Short update, since progress is going slower than I had hoped:

I extended the 2wt butt section by a couple inches and glued a reel seat and some cork rings on to it. Comparing it to my Gen 1 2100 ESN that I built out a few years ago, the RDP 5pc is a LOT lighter, but it still feels very capable without being a noodle. Looking forward to slapping guides on it and getting you guys a few pics and a casting review.


Top
  
PostPosted: Tue Aug 10, 2021 7:17 am • # 10 
User avatar
Sr. Member

Joined: 09/09/14
Posts: 469
Location: southern Brazil
Mr. Toothybugs, the suspense is killing me. Have you made any progress on your project?


Top
  
PostPosted: Tue Aug 10, 2021 7:35 am • # 11 
User avatar
Full Member

Joined: 02/06/13
Posts: 114
PampasPete wrote:
Mr. Toothybugs, the suspense is killing me. Have you made any progress on your project?


Cork is mostly ground down and guides are laid out but my lathe started acting a little wonky so I quit halfway through. Slowing things further, I have a 2yr old who HAS to be doing all the fun things that Dad is.


Top
  
PostPosted: Wed Oct 06, 2021 6:35 pm • # 12 
User avatar
Newbie

Joined: 12/15/12
Posts: 7
Mr Toothybugs, I'm with PampasPete: the suspense is killing me too!
Have you made any progress on your project?


Top
  
PostPosted: Thu Oct 07, 2021 11:37 am • # 13 
User avatar
Full Member

Joined: 02/06/13
Posts: 114
It kinda sucks to say this I haven't done a thing with this since the last update. A busy fall and delayed ability to fix my lathe rollers has put this at a much lower priority. Even more so now that my trout season is over with and ducks are starting up. However, I haven't stopped thinking about it by any stretch. Now completion is a spring target. Hopefully I can get some pictures of a finished build up before the holiday season hits.


Top
  
PostPosted: Thu Oct 28, 2021 8:59 am • # 14 
User avatar
Full Member

Joined: 02/06/13
Posts: 114
Brief update: lathe is 90% back up to where I need it to be, I still have to finish rebuilding my rollers but all the lathe housing is finished, ventilation (dust suction) complete, roller parts are assembled and laid out, and really just some minor cutting has to happen before I can call it done. Then I'll finish the grip, wrap the guides, and post pics.


Top
  
Display posts from previous:  Sort by  

  Page 1 of 1   [ 14 posts ] New Topic Add Reply

All times are UTC - 5 hours [ DST ]



Who is online

Users browsing this forum: No registered users and 4 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group

- OurBoard Support -